Used Post-Press machines for Sale
BOBST HEIDELBERG POLAR STAHL
Enlarge
Bobst SP 104 E
The machine was selected and carefully inspected by our engineers prior to purchase.
MACHINE SPECIFICATION
| Manufacturer | Bobst |
|---|---|
| Model | SP 104 E |
| Type | Die Cutting/fustellatrici |
TECHNICAL DATA
| Max sheet size | 1040 x 740 |
|---|---|
| Min sheet size | 350 x 400 |
Accessories
- Machine
- Platform with safety barrier
- Centerline system for quick job changeover
- Electronic device for sheet travel control
- Adjustable centering at the stripping and at the delivery
- Air conditioning for the electrical cabinet
- Gripper bars
- Bobst Electronic System for management of the machine
- Main motor with frequency variator
- F-9 PRE-SETTING TABLE : Adjustable. Allows the preparation of a second job during production, reducing machine makeready time and increasing the time available to run production. Requires: a series of supplementary stripping tools
- Feeder
- Pile-tray with handle allowing manual lateral correction of the pile during production
- Pile height control at the front edge thanks to a photoelectric cell
- Pile rear guide (OS and OOS sides)
- Adjustable lateral blowers with Centerline references
- Suction unit with multiple adjusting
- Safety system for lowering the pile try
- C-4 NON-STOP FEEDER MANUAL DEVICE
- C-8 VERTICAL POSITIONING OF THE SUCTION UNIT. Eliminates manual interventions to compensate for the flatness of the pile shape
- Introduction table
- Covered with an anti-static stainless steel plate
- 1 Inlet table feeder
- 4 front lays, adjustable in pairs with front register control
- 1 Pull-lay operator side (OS) adjustable according to Centerline, with sheet control
- 1 Double sheet detector
- Support plates at entry of platen station
- 1 Sheet-hold down device (guiding the sheets to front lays)
- 1 Upper frame with manual lifting device
- 1 Upper transport equipment for paper, paperboard and corrugated board
- 4 Transport belts. With lateral guidance
- C-5 CONTROLLABLE SHEET ARRIVAL FOR PERFECT SYNCHRONIZATION OF SHEET ARRIVAL AND REDUCTION OF MACHINE STOPPAGES
- Platin
- Grippers re-opening device
- Die-cutting device without band of gripper grip
- Equipment centering and locking
- Locking of the chase against the upper beam
- Measurement of the die-cutting force with strain gauge
- Resocell: synthetic material supporting plate. Thickness 22.5 mm
- 1 Upper chase with quick locking: fixed bottom (E-3) Plate, thickness 2 mm and make-ready protection plate of syntetic material, 1 mm thickness
- E-5 COMPENSATION PLATE 4 mm thickness. it's useful for thin plate for repetetive work
- E 55 ADJUSTABLE SUPPORTING PLATE CENTERINGS : micromeric screws allow fine adjustment of counters mounted on the cutting plate with respect to the die (+/- 0,9 mm lengthwise and crosswise.
- Stripping Station
- 3 drawer frame system
- 1 Upper Stripping Frame (F-2)
- 1 Upper stripping equipment (F-21) required to create a waste stripping tool, including crossbars, clamps, stripper holders and stripping pins of 3, 5 and 10 mm of diameter
- 1 Fastening equipment for stripping die (F-22)
- 1 lower pull-out frame (F-8)
- 1 Lower stripping equipment (F-81) Equipment for waste stripping including crossbars, pins and supports
- F-31 1 UPPER PULL-OUT FRAME QUICK LOCK. It reduces stripping tool assembly times; the quick-closing device allows the tool to be changed in the machine)
- F-72 1 CENTRAL PULL-OUT FRAME QUICK LOCK
- Delivery
- Pile tray in delivery
- Adjustable rear and side joggers with Centerline marks
- 1 Braking brush
- Pneumatically controlled adjustable front joggers
- G-5 AUTOMATIC NON-STOP ON DELIVERY
- Conformity to standards and security
- Operator safety devices
- Gripper Bar Chain Slip Clutch
- Gripper bar chain locking device
- Handling of the diecutting equipment
- Emergency Stops
Machine overview
| Year | 1997 |
|---|---|
| Serial Number | 057802905 |
| N.of working hours | 38460 |
“EXTRA” Accessories Overview
- F-9 PRE-SETTING TABLE : Adjustable. Allows the preparation of a second job during production, reducing machine makeready time and increasing the time available to run production. Requires: a series of supplementary stripping tools
- C-4 NON-STOP FEEDER MANUAL DEVICE
- C-8 VERTICAL POSITIONING OF THE SUCTION UNIT. Eliminates manual interventions to compensate for the flatness of the pile shape
- C-5 CONTROLLABLE SHEET ARRIVAL FOR PERFECT SYNCHRONIZATION OF SHEET ARRIVAL AND REDUCTION OF MACHINE STOPPAGES
- E-5 COMPENSATION PLATE 4 mm thickness. it's useful for thin plate for repetetive work
- E 55 ADJUSTABLE SUPPORTING PLATE CENTERINGS : micromeric screws allow fine adjustment of counters mounted on the cutting plate with respect to the die (+/- 0,9 mm lengthwise and crosswise.
- F-31 1 UPPER PULL-OUT FRAME QUICK LOCK. It reduces stripping tool assembly times; the quick-closing device allows the tool to be changed in the machine)
- F-72 1 CENTRAL PULL-OUT FRAME QUICK LOCK
- G-5 AUTOMATIC NON-STOP ON DELIVERY
Reference Overview
| Reference | 25036495 |
|---|---|
| Visible | In production |
| Availability | Immediately |
Note:
Die Cutting test possible with your jobs by appointment
Contacts
Camporese Macchine Grafiche S.p.A
Via Del Santo, 243 - 35010 - Limena (Padova) Italy
+39 049 767166
+39 049 767629
info@camporese.it
Partita Iva IT03429400280
Euro 2.000.000,00 issued and fully paid-up share capital
Via Del Santo, 243 - 35010 - Limena (Padova) Italy
+39 049 767166
+39 049 767629
info@camporese.it
Partita Iva IT03429400280
Euro 2.000.000,00 issued and fully paid-up share capital
Euro 5.495.000,00 net asset
Newsletter
Stay tuned to Camporese offers!
